2010 CPU: ARMv6-compatible processor [4117b363] revision 3 (ARMv6TEJ), cr=00c5387f Machine: Logitech Fab4 Board Memory policy: ECC disabled, Data cache writeback On node 0 totalpages: 32768 DMA zone: 48 pages used for memmap DMA zone: 0 pages reserved DMA zone: 6096 pages, LIFO batch:0 Normal zone: 208 pages used for memmap Normal zone: 26416 pages, LIFO batch:7 Movable zone: 0 pages used for memmap CPU0: D VIPT write-back cache CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets Real-Time Preemption Support (C) 2004-2007 Ingo Molnar Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 Kernel command line: console=ttymxc0,115200 noinitrd init=/linuxrc ubi.mtd=1 roo t=/dev/mtdblock:cramfs Preemptible RCU implementation. MXC IRQ initialized PID hash table entries: 512 (order: 9, 2048 bytes) MXC GPT timer initialized, rate = 16625000 WARNING: Clock divider has been truncated, clock error 150 [ps] per 60 [ns] Console: colour dummy device 80x30 Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 128MB = 128MB total Memory: 125696KB available (3732K code, 316K data, 152K init) Calibrating delay loop... 530.84 BogoMIPS (lpj=2654208) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok net_namespace: 276 bytes NET: Registered protocol family 16 L2X0 cache controller enabled CPU is i.MX0 Revision 0.5 Clock input source is 24000000 MXC GPIO hardware Reset status: Watchdog timeout Using SDMA I.API MXC DMA API initialized SCSI subsystem initialized CSPI: mxc_spi-0 probed usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb MXC I2C driver clk: Unable to get requested clock: dfm_clk ASoC version 0.20 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 4, 114688 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NET: Registered protocol family 1 usb: DR host (utmi) registered krcupreemptd setsched 0 prio = 98 Registering unionfs 2.5.1 (for 2.6.26.8) fuse init (API version 7.9) msgmni has been set to 245 io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) mxc_ipu mxc_ipu: Channel already uninitialized 14 Console: switching to colour frame buffer device 60x34 mxc_ipu mxc_ipu: Channel already uninitialized 15 mxcfb: fb registered, using mode fsl_rngc fsl_rngc: FSL RNGC Registered. Serial: MXC Internal UART driver mxcintuart.0: ttymxc0 at MMIO 0x43f90000 (irq = 45) is a Freescale MXC console [ttymxc0] enabled mxcintuart.1: ttymxc1 at MMIO 0x43f94000 (irq = 32) is a Freescale MXC loop: module loaded FEC ENET Version 0.2 fec: PHY @ 0x1, ID 0x00008201 -- RTL8210CP eth0: ethernet 00:04:20:22:01:8e Driver 'sd' needs updating - please use bus_type methods MXC MTD nand Driver 2.5 NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bi t) Bad block table found at page 65472, version 0x01 Bad block table found at page 65408, version 0x01 nand_read_bbt: Bad block at 0x011a0000 nand_read_bbt: Bad block at 0x022e0000 nand_read_bbt: Bad block at 0x02700000 nand_read_bbt: Bad block at 0x02860000 nand_read_bbt: Bad block at 0x07440000 RedBoot partition parsing not available cmdlinepart partition parsing not available Creating 2 MTD partitions on "NAND 128MiB 3,3V 8-bit": 0x00000000-0x00080000 : "redboot" 0x00080000-0x07f40000 : "ubi" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 129024 bytes UBI: smallest flash I/O unit: 2048 UBI: sub-page size: 512 UBI: VID header offset: 512 (aligned 512) UBI: data offset: 2048 UBI: attached mtd1 to ubi0 UBI: MTD device name: "ubi" UBI: MTD device size: 126 MiB UBI: number of good PEBs: 1009 UBI: number of bad PEBs: 5 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 5 UBI: available PEBs: 308 UBI: total number of reserved PEBs: 701 UBI: number of PEBs reserved for bad PEB handling: 10 UBI: max/mean erase counter: 1123/59 UBI: background thread "ubi_bgt0d" started, PID 300 fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1 eth0: status: link up, 100MBit Full Duplex, auto-negotiation complete. fsl-ehci fsl-ehci.0: irq 37, io mem 0x53ff4000 fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected Initializing USB Mass Storage driver... usb 1-1: new low speed USB device using fsl-ehci and address 2 usb 1-1: configuration #1 chosen from 1 choice usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbserial usbserial: USB Serial support registered for generic usbcore: registered new interface driver usbserial_generic usbserial: USB Serial Driver core usbserial: USB Serial support registered for FTDI USB Serial Device usbcore: registered new interface driver ftdi_sio ftdi_sio: v1.4.3:USB FTDI Serial Converters Driver usbserial: USB Serial support registered for Keyspan - (without firmware) usbserial: USB Serial support registered for Keyspan 1 port adapter usbserial: USB Serial support registered for Keyspan 2 port adapter usbserial: USB Serial support registered for Keyspan 4 port adapter usbcore: registered new interface driver keyspan keyspan: v1.1.5:Keyspan USB to Serial Converter Driver usbserial: USB Serial support registered for pl2303 usbcore: registered new interface driver pl2303 pl2303: Prolific PL2303 USB to serial adaptor driver mice: PS/2 mouse device common for all mice i2c /dev entries driver Clearpad: TM1199Logitech (7552,4248) input: Synaptics ClearPad as /class/input/input0 tsl2569 0-0039: support ver. 1.0 enabled i2c-adapter i2c-0: ACK not received lm75: probe of 0-0048 failed with error -1 MXC WatchDog Driver 2.0 MXC Watchdog # 0 Timer: initial timeout 60 sec IPU Post-filter loading mxc_asrc registered input: FAB4 IR as /class/input/input1 firmware: requesting ir_controller_21323.hex mxsdhci: MXC Secure Digital Host Controller Interface driver mxsdhci: MXC SDHCI Controller Driver. mmc0: SDHCI detect irq 0 irq 7 INTERNAL DMA mxsdhci: MXC SDHCI Controller Driver. mmc1: SDHCI detect irq 102 irq 8 INTERNAL DMA mmc0: new SDIO card at address 0001 input: Logitech Logitech USB Keyboard as /class/input/input2 input: USB HID v1.10 Keyboard [Logitech Logitech USB Keyboard] on usb-fsl-ehci.0 -1 usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver Advanced Linux Sound Architecture Driver Version 1.0.16. MXC spdif support initialized usbcore: registered new interface driver snd-usb-audio AK4420 Audio Codec 0.1<6>DMA Sound Buffers Allocated:UseIram=0 buf->addr=87eb000 0 buf->area=fe004000 size=65536 asoc: ak4420-dai <-> imx-ssi-1 mapping ok WM8974 Audio Codec 0.1 DMA Sound Buffers Allocated:UseIram=0 buf->addr=87ed0000 buf->area=fe014000 size =65536 DMA Sound Buffers Allocated:UseIram=0 buf->addr=87ee0000 buf->area=fe024000 size =65536 asoc: wm8974-hifi-dai <-> imx-ssi-3 mapping ok fab4 WM8974 Audio Driver ALSA device list: #0: MXC Freescale with SPDIF #1: fab4 (ak4420) #2: fab4 (wm8974) oprofile: using arm/armv6 TCP cubic registered NET: Registered protocol family 17 RPC: Registered udp transport module. RPC: Registered tcp transport module. ieee80211: 802.11 data/management/control stack, git-1.1.13 ieee80211: Copyright (C) 2004-2005 Intel Corporation ieee80211_crypt: registered algorithm 'NULL' mxc_rtc mxc_rtc.0: rtc core: registered mxc_rtc as rtc0 No external RTC clock Real TIme clock Driver v1.0 mxc_rtc: probe of mxc_rtc.0 failed with error -2 Static Power Management for Freescale i.MX35 VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 3 MXC Backlight Device mxc_ipu_bl.0 Initialized. platform mxc_rtc.0: setting system clock to 1970-01-03 00:12:56 UTC (173576) VFS: Mounted root (cramfs filesystem) readonly. Freeing init memory: 152K UBIFS: recovery needed UBIFS: recovery completed UBIFS: mounted UBI device 0, volume 2, name "ubifs" UBIFS: file system size: 19869696 bytes (19404 KiB, 18 MiB, 154 LEBs) UBIFS: journal size: 1032193 bytes (1008 KiB, 0 MiB, 8 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: lzo UBIFS: reserved for root: 938494 bytes (916 KiB) firmware: requesting helper_sd.bin firmware: requesting sd8686.bin eth0: config: auto-negotiation on, 100FDX, 100HDX, 10FDX, 10HDX. eth0: status: link down. eth0: status: link up, 100MBit Full Duplex, auto-negotiation complete. fab4 ir: set proximity control: (4,0): 40 i2c-adapter i2c-0: ACK not received tsl2569: set timing: (1,2): 12 Store Gain: 1 Store Factor: 40 CMD_RESP: cmd 0x801f error, result=0x1 FAB4 IR: fw checksum ok aa33 #