root: wlan started Starting SqueezePlay Please press Enter to activate this console. udhcpc (v1.15.2) started killall: zcip: no process killed Sending discover... Squeezeplay 7.5.0 r8673 Sending discover... Sending discover... killall: zcip: no process killed No lease, forking to background [ 33.689510] channel hint set to 2412 [ 33.749636] AR6000 connected event on freq 2412 with bssid 00:1b:2f:4a:c0:da listenInterval=100, beaconInterval = 100, beaconIeLen = 24 assocReqLen=52 assoc RespLen =22 [ 33.764845] Network: Infrastructure ++NAND: RCSR=54200900 Searching for BBT table in the flash ... . Found version 1 Bbt0 at block 1023 (0x7fe0000) Block 110 is bad Block 231 is bad Block 420 is bad Block 593 is bad Total bad blocks: 4 .FEC PHY: RTL8201EL FEC: [ HALF_DUPLEX ] [ disconnected ] [ 10M bps ]: Ethernet mxc_fec: MAC address 00:04:20:26:8e:ec No IP info for device! Unrecognized chip: 0xf8!!! hardware reset by POR Clock input is 24 MHz RedBoot(tm) bootstrap and debug environment [ROMRAM] Non-certified release, version FSL 200904 - built 15:05:21, Aug 11 2009 Platform: Logitech Baby (i.MX25 ) PASS 1.0 [x32 DDR] System type 2070 revision 5 Copyright (C) 2000, 2001, 2002, 2003, 2004 Red Hat, Inc. Copyright (C) 2003, 2004, 2005, 2006 eCosCentric Limited RAM: 0x00000000-0x03f00000, [0x00095250-0x03ef1000] available FLASH: 0x00000000 - 0x8000000, 1024 blocks of 0x00020000 bytes each. RedBoot> ubi attach -f 0x80000 -l 0x07EC0000 -w 0x800 -e 0x20000 -s 0x200 scanning 1014 PEBs ................................................................................ ................................................................................ ....................................................skipping bad block 106 ................................................................................ ................................................................................ ................................................................................ skipping bad block 227 ................................................................................ ................................................................................ ................................................................................ ................................................................................ ........................................................skipping bad block 416 ................................................................................ ................................................................................ ................................................................................ ................................................................................ ........................skipping bad block 589 ................................................................................ ................................................................................ ................................................................................ ................................................................................ ................................................................................ ................................................................................ ................................................................................ ................................................................................ ................................................................................ ................................................................................ ................................................scanning is finished RedBoot> ubi load -b 0x100000 kernel%{os_backup} RedBoot> exec -c %{os_cmdline}entry=0x80008000, target=0x80008000 Using base address 0x00100000 and length 0x002d4800 [ 0.000000] Linux version 2.6.26.8-rt16 (parabuild@vdc01b01centos02) (gcc ver sion 4.4.1 (Sourcery G++ Lite 2009q3-67) ) #1 PREEMPT RT Thu Feb 18 21:49:04 MST 2010 [ 0.000000] CPU: ARM926EJ-S [41069264] revision 4 (ARMv5TEJ), cr=00053177 [ 0.000000] Machine: Logitech MX25 Baby Board [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] CPU0: D VIVT write-back cache [ 0.000000] CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 s ets [ 0.000000] CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 s ets [ 0.000000] Real-Time Preemption Support (C) 2004-2007 Ingo Molnar [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 16256 [ 0.000000] Kernel command line: console=ttymxc1,115200 noinitrd init=/linuxr c ubi.mtd=1 root=/dev/mtdblock:cramfs [ 0.000000] Preemptible RCU implementation. [ 0.000000] MXC IRQ initialized [ 0.000000] PID hash table entries: 256 (order: 8, 1024 bytes) [ 0.000000] MXC GPT timer initialized, rate = 12000000 [ 0.000000] WARNING: Clock divider has been truncated, clock error 333 [ps] p er 83 [ns] [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Memory: 64MB = 64MB total [ 0.000000] Memory: 61984KB available (2576K code, 248K data, 120K init) [ 0.000000] Mount-cache hash table entries: 512 [ 0.000000] CPU: Testing write buffer coherency: ok [ 0.000000] net_namespace: 276 bytes [ 0.000000] NET: Registered protocol family 16 [ 0.000000] AIPS1 VA base: 0xfc000000 [ 0.000000] CPU is i.MX0 Revision 0.5 [ 0.000000] Clock input source is 24000000 [ 0.000000] MXC GPIO hardware [ 0.000000] Using SDMA I.API [ 0.000000] MXC DMA API initialized [ 0.000000] epit_clk: 66500000 [ 0.000000] per_epit_clk: 66500000 [ 0.000000] ahb_clk: 133000000 [ 0.000000] cpu_clk: 399000000 [ 0.000000] mpll: 532000000 [ 0.000000] osc24m: 24000000 [ 0.000133] MXC EPIT timer initialized, rate = 16625000 4 [ 0.029131] MXC I2C driver [ 0.031674] MXC I2C driver [ 0.035943] ASoC version 0.20 [ 0.131044] NET: Registered protocol family 1 [ 0.133786] Bus freq driver module loaded [ 0.137962] krcupreemptd setsched 0 [ 0.138002] prio = 98 [ 0.140470] Registering unionfs 2.5.1 (for 2.6.26.8) [ 0.141498] msgmni has been set to 121 [ 0.141829] io scheduler noop registered [ 0.141867] io scheduler anticipatory registered [ 0.141894] io scheduler deadline registered [ 0.142101] io scheduler cfq registered (default) [ 0.146669] **** baby_lcd_spi_init [ 0.379159] Console: switching to colour frame buffer device 30x40 [ 0.384790] mxc_sdc_fb mxc_sdc_fb.0: fb0: DISP0 BG fb device registered succe ssfully. [ 0.389650] mxc_sdc_fb mxc_sdc_fb.0: fb1: DISP0 FG fb device registered succe ssfully. [ 0.392848] MXC Backlight Device mxc_lcdc_bl.0 Initialized. [ 0.466896] Serial: MXC Internal UART driver [ 0.467302] mxcintuart.1: ttymxc1 at MMIO 0x43f94000 (irq = 32) is a Freescal e MXC [ 0.467411] console [ttymxc1] enabled [ 0.796996] brd: module loaded [ 0.820422] loop: module loaded [ 0.823673] FEC ENET Version 0.2 [ 0.828766] fec: PHY @ 0x1, ID 0x001cc815 -- RTL8201E [ 0.835895] eth0: ethernet 00:04:20:26:8e:ec [ 0.842054] MXC MTD nand Driver 2.5 [ 0.846909] NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 1 28MiB 3,3V 8-bit) [ 0.857459] Searching for RedBoot partition table in NAND 128MiB 3,3V 8-bit a t offset 0x7f60000 [ 0.877392] No RedBoot partition table detected in NAND 128MiB 3,3V 8-bit [ 0.884492] Creating 2 MTD partitions on "NAND 128MiB 3,3V 8-bit": [ 0.890916] 0x00000000-0x00080000 : "redboot" [ 0.900242] 0x00080000-0x07f40000 : "ubi" [ 0.911927] UBI: attaching mtd1 to ubi0 [ 0.915819] UBI: physical eraseblock size: 131072 bytes (128 KiB) [ 0.922134] UBI: logical eraseblock size: 129024 bytes [ 0.927567] UBI: smallest flash I/O unit: 2048 [ 0.932305] UBI: sub-page size: 512 [ 0.936956] UBI: VID header offset: 512 (aligned 512) [ 0.942827] UBI: data offset: 2048 [ 1.185159] UBI: attached mtd1 to ubi0 [ 1.188955] UBI: MTD device name: "ubi" [ 1.193785] UBI: MTD device size: 126 MiB [ 1.198788] UBI: number of good PEBs: 1010 [ 1.203528] UBI: number of bad PEBs: 4 [ 1.208001] UBI: max. allowed volumes: 128 [ 1.212652] UBI: wear-leveling threshold: 4096 [ 1.217388] UBI: number of internal volumes: 1 [ 1.221866] UBI: number of user volumes: 5 [ 1.226343] UBI: available PEBs: 516 [ 1.230992] UBI: total number of reserved PEBs: 494 [ 1.235904] UBI: number of PEBs reserved for bad PEB handling: 10 [ 1.242037] UBI: max/mean erase counter: 15/6 [ 1.246458] UBI: background thread "ubi_bgt0d" started, PID 280 [ 1.254716] mice: PS/2 mouse device common for all mice [ 1.260003] MXC keypad loaded [ 1.264725] input: mxckpd as /class/input/input0 [ 1.473577] MXC WatchDog Driver 2.0 [ 1.478489] MXC Watchdog # 0 Timer: initial timeout 60 sec [ 1.491238] input: front panel as /class/input/input1 [ 1.714756] input: msp430 as /class/input/input2 [ 1.833418] msp430 1-0010: rtc core: registered msp430 as rtc0 [ 1.841137] Requesting msp430 firmware msp430-0005.txt [ 1.847659] firmware: requesting msp430-0005.txt [ 1.856490] i.MX ADC at 0x50030000 irq 46 [ 1.861851] mxsdhci: MXC Secure Digital Host Controller Interface driver [ 1.868796] mxsdhci: MXC SDHCI Controller Driver. [ 1.910815] mmc0: SDHCI detect irq 0 irq 9 PIO [ 1.971414] Advanced Linux Sound Architecture Driver Version 1.0.16. [ 2.082373] AIC3104 Audio Codec 0.1<6>DMA Sound Buffers Allocated:UseIram=1 b uf->addr=78001000 buf->area=c4860000 size=65536 [ 2.095065] DMA Sound Buffers Allocated:UseIram=1 buf->addr=83e20000 buf->are a=fde97000 size=65536 [ 2.104089] asoc: aic3104-dai <-> imx-ssi-1 mapping ok [ 2.250958] ALSA device list: [ 2.253976] #0: baby (aic3104) [ 2.257224] oprofile: using timer interrupt. [ 2.262365] NET: Registered protocol family 2 [ 2.378470] mmc0: new SDIO card at address 0001 [ 2.591880] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 2.604735] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 2.612788] TCP bind hash table entries: 2048 (order: 3, 57344 bytes) [ 2.620952] TCP: Hash tables configured (established 2048 bind 2048) [ 2.627353] TCP reno registered [ 2.745862] TCP cubic registered [ 2.749155] NET: Registered protocol family 17 [ 2.765148] msp430 1-0010: setting system clock to 1970-01-01 02:20:36 UTC (8 436) [ 2.779307] VFS: Mounted root (cramfs filesystem) readonly. [ 2.785775] Freeing init memory: 120K [ 3.874841] UBIFS: recovery needed [ 3.917645] UBIFS: recovery completed [ 3.921385] UBIFS: mounted UBI device 0, volume 2, name "ubifs" [ 3.927357] UBIFS: file system size: 9418752 bytes (9198 KiB, 8 MiB, 73 LEB s) [ 3.934720] UBIFS: journal size: 1032193 bytes (1008 KiB, 0 MiB, 6 LEBs ) [ 3.941998] UBIFS: media format: w4/r0 (latest is w4/r0) [ 3.947868] UBIFS: default compressor: lzo [ 3.951999] UBIFS: reserved for root: 444870 bytes (434 KiB) Filesystem overlay: unionfs mount: mounting /dev on /mnt/overlay/dev failed: Invalid argument init started: BusyBox v1.15.2 (2010-02-18 22:20:48 MST) starting pid 365, tty '': '/etc/init.d/rcS' Starting udev Mounting RAM Disk Starting syslogd [ 13.900244] msp430: firmware ok (1316) root: No bootloader for board: 0005 Starting lo Starting inetd root: wlan: starting Setting eth1 macaddr: 00:04:20:26:8E:EC Load Board Data from /lib/atheros/calData_ar6102_15dBm.bin Updating MAC address BMI Write Memory (address: 0x502400, filename: /lib/atheros/athwlan.bin) BMI Write Memory (address: 0x52d8bc, filename: /lib/atheros/data.patch.hw2_0.bin ) BMI Write Memory (address: 0x500418, value: 0x52d8bc) BMI Bit-Wise (OR) modify Register (address: 0x500410, orig:0x0, new: 0x1, mask: 0x1) BMI Done [ 16.347014] AR6000 Reg Code = 0x40000060 Selected interface 'eth1' root: wlan started Starting SqueezePlay Please press Enter to activate this console. udhcpc (v1.15.2) started killall: zcip: no process killed Sending discover... Squeezeplay 7.5.0 r8673 Sending discover... [ 23.799014] channel hint set to 2412 [ 23.850991] AR6000 connected event on freq 2412 with bssid 00:1b:2f:4a:c0:da listenInterval=100, beaconInterval = 100, beaconIeLen = 24 assocReqLen=52 assoc RespLen =22 [ 23.866180] Network: Infrastructure Performing a DHCP renew Sending discover... Sending select for 192.168.1.6... Lease of 192.168.1.6 obtained, lease time 86400 killall: zcip: no process killed route: SIOCDELRT: No such process adding dns 192.168.1.1 ++NAND: RCSR=54200900 Searching for BBT table in the flash ... . Found version 1 Bbt0 at block 1023 (0x7fe0000) Block 110 is bad Block 231 is bad Block 420 is bad Block 593 is bad Total bad blocks: 4 .FEC PHY: RTL8201EL FEC: [ HALF_DUPLEX ] [ disconnected ] [ 10M bps ]: Ethernet mxc_fec: MAC address 00:04:20:26:8e:ec No IP info for device! Unrecognized chip: 0xf8!!! hardware reset by POR Clock input is 24 MHz RedBoot(tm) bootstrap and debug environment [ROMRAM] Non-certified release, version FSL 200904 - built 15:05:21, Aug 11 2009 Platform: Logitech Baby (i.MX25 ) PASS 1.0 [x32 DDR] System type 2070 revision 5 Copyright (C) 2000, 2001, 2002, 2003, 2004 Red Hat, Inc. Copyright (C) 2003, 2004, 2005, 2006 eCosCentric Limited RAM: 0x00000000-0x03f00000, [0x00095250-0x03ef1000] available FLASH: 0x00000000 - 0x8000000, 1024 blocks of 0x00020000 bytes each. RedBoot> ubi attach -f 0x80000 -l 0x07EC0000 -w 0x800 -e 0x20000 -s 0x200 scanning 1014 PEBs ................................................................................ ................................................................................ ....................................................skipping bad block 106 ................................................................................ ................................................................................ ................................................................................ skipping bad block 227 ................................................................................ ................................................................................ ................................................................................ ................................................................................ ........................................................skipping bad block 416 ................................................................................ ................................................................................ ................................................................................ ................................................................................ ........................skipping bad block 589 ................................................................................ ................................................................................ ................................................................................ ................................................................................ ................................................................................ ................................................................................ ................................................................................ ................................................................................ ................................................................................ ................................................................................ ................................................scanning is finished RedBoot> ubi load -b 0x100000 kernel%{os_backup} RedBoot> exec -c %{os_cmdline}entry=0x80008000, target=0x80008000 Using base address 0x00100000 and length 0x002d4800 [ 0.000000] Linux version 2.6.26.8-rt16 (parabuild@vdc01b01centos02) (gcc ver sion 4.4.1 (Sourcery G++ Lite 2009q3-67) ) #1 PREEMPT RT Thu Feb 18 21:49:04 MST 2010 [ 0.000000] CPU: ARM926EJ-S [41069264] revision 4 (ARMv5TEJ), cr=00053177 [ 0.000000] Machine: Logitech MX25 Baby Board [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] CPU0: D VIVT write-back cache [ 0.000000] CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 s ets [ 0.000000] CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 s ets [ 0.000000] Real-Time Preemption Support (C) 2004-2007 Ingo Molnar [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 16256 [ 0.000000] Kernel command line: console=ttymxc1,115200 noinitrd init=/linuxr c ubi.mtd=1 root=/dev/mtdblock:cramfs [ 0.000000] Preemptible RCU implementation. [ 0.000000] MXC IRQ initialized [ 0.000000] PID hash table entries: 256 (order: 8, 1024 bytes) [ 0.000000] MXC GPT timer initialized, rate = 12000000 [ 0.000000] WARNING: Clock divider has been truncated, clock error 333 [ps] p er 83 [ns] [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Memory: 64MB = 64MB total [ 0.000000] Memory: 61984KB available (2576K code, 248K data, 120K init) [ 0.000000] Mount-cache hash table entries: 512 [ 0.000000] CPU: Testing write buffer coherency: ok [ 0.000000] net_namespace: 276 bytes [ 0.000000] NET: Registered protocol family 16 [ 0.000000] AIPS1 VA base: 0xfc000000 [ 0.000000] CPU is i.MX0 Revision 0.5 [ 0.000000] Clock input source is 24000000 [ 0.000000] MXC GPIO hardware [ 0.000000] Using SDMA I.API [ 0.000000] MXC DMA API initialized [ 0.000000] epit_clk: 66500000 [ 0.000000] per_epit_clk: 66500000 [ 0.000000] ahb_clk: 133000000 [ 0.000000] cpu_clk: 399000000 [ 0.000000] mpll: 532000000 [ 0.000000] osc24m: 24000000 [ 0.000136] MXC EPIT timer initialized, rate = 16625000 4 [ 0.029175] MXC I2C driver [ 0.031721] MXC I2C driver [ 0.035976] ASoC version 0.20 [ 0.131036] NET: Registered protocol family 1 [ 0.133763] Bus freq driver module loaded [ 0.137930] krcupreemptd setsched 0 [ 0.137968] prio = 98 [ 0.140431] Registering unionfs 2.5.1 (for 2.6.26.8) [ 0.141463] msgmni has been set to 121 [ 0.141797] io scheduler noop registered [ 0.141835] io scheduler anticipatory registered [ 0.141862] io scheduler deadline registered [ 0.142068] io scheduler cfq registered (default) [ 0.146642] **** baby_lcd_spi_init [ 0.379169] Console: switching to colour frame buffer device 30x40 [ 0.384792] mxc_sdc_fb mxc_sdc_fb.0: fb0: DISP0 BG fb device registered succe ssfully. [ 0.389646] mxc_sdc_fb mxc_sdc_fb.0: fb1: DISP0 FG fb device registered succe ssfully. [ 0.392826] MXC Backlight Device mxc_lcdc_bl.0 Initialized. [ 0.467001] Serial: MXC Internal UART driver [ 0.467414] mxcintuart.1: ttymxc1 at MMIO 0x43f94000 (irq = 32) is a Freescal e MXC [ 0.467521] console [ttymxc1] enabled [ 0.797079] brd: module loaded [ 0.820538] loop: module loaded [ 0.823788] FEC ENET Version 0.2 [ 0.828882] fec: PHY @ 0x1, ID 0x001cc815 -- RTL8201E [ 0.836014] eth0: ethernet 00:04:20:26:8e:ec [ 0.842152] MXC MTD nand Driver 2.5 [ 0.847031] NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 1 28MiB 3,3V 8-bit) [ 0.857570] Searching for RedBoot partition table in NAND 128MiB 3,3V 8-bit a t offset 0x7f60000 [ 0.877388] No RedBoot partition table detected in NAND 128MiB 3,3V 8-bit [ 0.884488] Creating 2 MTD partitions on "NAND 128MiB 3,3V 8-bit": [ 0.890907] 0x00000000-0x00080000 : "redboot" [ 0.900230] 0x00080000-0x07f40000 : "ubi" [ 0.911911] UBI: attaching mtd1 to ubi0 [ 0.915800] UBI: physical eraseblock size: 131072 bytes (128 KiB) [ 0.922115] UBI: logical eraseblock size: 129024 bytes [ 0.927551] UBI: smallest flash I/O unit: 2048 [ 0.932291] UBI: sub-page size: 512 [ 0.936941] UBI: VID header offset: 512 (aligned 512) [ 0.942814] UBI: data offset: 2048 [ 1.185369] UBI: attached mtd1 to ubi0 [ 1.189166] UBI: MTD device name: "ubi" [ 1.194001] UBI: MTD device size: 126 MiB [ 1.199003] UBI: number of good PEBs: 1010 [ 1.203741] UBI: number of bad PEBs: 4 [ 1.208220] UBI: max. allowed volumes: 128 [ 1.212871] UBI: wear-leveling threshold: 4096 [ 1.217614] UBI: number of internal volumes: 1 [ 1.222090] UBI: number of user volumes: 5 [ 1.226566] UBI: available PEBs: 516 [ 1.231218] UBI: total number of reserved PEBs: 494 [ 1.236129] UBI: number of PEBs reserved for bad PEB handling: 10 [ 1.242261] UBI: max/mean erase counter: 15/6 [ 1.246684] UBI: background thread "ubi_bgt0d" started, PID 280 [ 1.254919] mice: PS/2 mouse device common for all mice [ 1.260208] MXC keypad loaded [ 1.264941] input: mxckpd as /class/input/input0 [ 1.473569] MXC WatchDog Driver 2.0 [ 1.478480] MXC Watchdog # 0 Timer: initial timeout 60 sec [ 1.491266] input: front panel as /class/input/input1 [ 1.714780] input: msp430 as /class/input/input2 [ 1.833410] msp430 1-0010: rtc core: registered msp430 as rtc0 [ 1.841116] Requesting msp430 firmware msp430-0005.txt [ 1.847623] firmware: requesting msp430-0005.txt [ 1.856481] i.MX ADC at 0x50030000 irq 46 [ 1.861834] mxsdhci: MXC Secure Digital Host Controller Interface driver [ 1.868786] mxsdhci: MXC SDHCI Controller Driver. [ 1.910811] mmc0: SDHCI detect irq 0 irq 9 PIO [ 1.971415] Advanced Linux Sound Architecture Driver Version 1.0.16. [ 2.082373] AIC3104 Audio Codec 0.1<6>DMA Sound Buffers Allocated:UseIram=1 b uf->addr=78001000 buf->area=c4860000 size=65536 [ 2.095075] DMA Sound Buffers Allocated:UseIram=1 buf->addr=83e20000 buf->are a=fde97000 size=65536 [ 2.104101] asoc: aic3104-dai <-> imx-ssi-1 mapping ok [ 2.251200] ALSA device list: [ 2.254214] #0: baby (aic3104) [ 2.257462] oprofile: using timer interrupt. [ 2.272666] NET: Registered protocol family 2 [ 2.378785] mmc0: new SDIO card at address 0001 [ 2.631830] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 2.645120] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 2.653175] TCP bind hash table entries: 2048 (order: 3, 57344 bytes) [ 2.661342] TCP: Hash tables configured (established 2048 bind 2048) [ 2.667742] TCP reno registered [ 2.795887] TCP cubic registered [ 2.799183] NET: Registered protocol family 17 [ 2.814146] i2c-adapter i2c-1: ACK not received [ 2.818843] msp430 1-0010: hctosys: unable to read the hardware clock [ 2.832095] VFS: Mounted root (cramfs filesystem) readonly. [ 2.838521] Freeing init memory: 120K [ 3.928077] UBIFS: recovery needed [ 3.966969] UBIFS: recovery completed [ 3.971130] UBIFS: mounted UBI device 0, volume 2, name "ubifs" [ 3.977104] UBIFS: file system size: 9418752 bytes (9198 KiB, 8 MiB, 73 LEB s) [ 3.984465] UBIFS: journal size: 1032193 bytes (1008 KiB, 0 MiB, 6 LEBs ) [ 3.991741] UBIFS: media format: w4/r0 (latest is w4/r0) [ 3.997610] UBIFS: default compressor: lzo [ 4.001741] UBIFS: reserved for root: 444870 bytes (434 KiB) Filesystem overlay: unionfs mount: mounting /dev on /mnt/overlay/dev failed: Invalid argument init started: BusyBox v1.15.2 (2010-02-18 22:20:48 MST) starting pid 365, tty '': '/etc/init.d/rcS' Starting udev Mounting RAM Disk Starting syslogd [ 13.902076] i2c-adapter i2c-1: ACK not received [ 13.906767] Couldn't read msp ID register, resetting mcu root: No bootloader for board: 0005 Starting lo Starting inetd root: wlan: starting Setting eth1 macaddr: 00:04:20:26:8E:EC Load Board Data from /lib/atheros/calData_ar6102_15dBm.bin Updating MAC address BMI Write Memory (address: 0x502400, filename: /lib/atheros/athwlan.bin) [ 15.461185] i2c-adapter i2c-1: ACK not received [ 15.465889] Couldn't read msp ID register, resetting mcu BMI Write Memory (address: 0x52d8bc, filename: /lib/atheros/data.patch.hw2_0.bin ) BMI Write Memory (address: 0x500418, value: 0x52d8bc) BMI Bit-Wise (OR) modify Register (address: 0x500410, orig:0x0, new: 0x1, mask: 0x1) BMI Done [ 16.760874] msp430: upgrade (-1 to 1316) [ 27.117572] AR6000 Reg Code = 0x40000060 bmiloader: eth1: Input/output error [ 27.233644] debug_hdr_ptr: 0x5018f0 [ 28.162431] msp430: upgrade complete (1316) Selected interface 'eth1' root: wlan started Starting SqueezePlay Please press Enter to activate this console. udhcpc (v1.15.2) started killall: zcip: no process killed Sending discover... Squeezeplay 7.5.0 r8673 Sending discover... Sending discover... killall: zcip: no process killed No lease, forking to background